| 25KG·CM STALL | 0.070S/60° NO-LOAD | 8.4V RATED |
| 77G WEIGHT | StainlessGEARTRAIN | 360°TRAVELCustomizable |
Overview
The BLS8125D is a 25 kg·cm brushless servo in the standard 20 × 40 × 38.4 mm case, 77 g. It is the direct brushless alternative to a coreless servo of the same size: same mounting, same 25T output, no brushes to wear.
The geartrain is stainless steel on two ball bearings, the horn is POM, and the case is CNC aluminium with the fins cut into the sides. The mechanical limit is 210°, the dead band is 1 µs, and the pulse window is the standard 800–2200 µs.
This page covers the TTL build: the same mechanics, commanded over a serial bus so several servos can share one signal line and be addressed individually. Useful when the actuator count outgrows the PWM channels available.
Performance at each supply voltage
| Supply | No-load speed | Peak stall torque | Idle current | Stall current |
|---|---|---|---|---|
| 6.0 V | 0.120 s/60° (500 °/s) | 18 kg·cm (1.77 N·m / 250 oz·in) | 300 mA | 2.8 A |
| 7.4 V | 0.090 s/60° (667 °/s) | 22 kg·cm (2.16 N·m / 306 oz·in) | 350 mA | 3.5 A |
| 8.4 V | 0.070 s/60° (857 °/s) | 25 kg·cm (2.45 N·m / 347 oz·in) | 410 mA | 4.0 A |
Control specification
| Item | Specification |
|---|---|
| Command signal | TTL serial |
| Amplifier | Digital controller |
| Dead band | 1 µs |
| Rotating direction | CCW (1000–2000 µs) |
| Travel | 360°, customizable |
Mechanical specification
| Item | Specification | Item | Specification |
|---|---|---|---|
| Dimensions | 20 × 40 × 38.4 mm | Case material | Aluminium, CNC |
| Weight | 77 g | Geartrain | Stainless steel |
| Bearings | 2 × ball bearing | Motor | Brushless |
| Output spline | 25T-φ5.94 mm | Horn | Plastic, POM |
| Lead / connector | 300 mm, 3-wire | Mechanical limit | 210° |
| Operating temperature | −15 °C to 65 °C | Storage temperature | −20 °C to 70 °C |
| Ingress protection | Splash resistant (customizable) | Travel | 360°, customizable |
What’s in the box
- 1 × XQ-BLS8125TTL servo
- 1 × POM horn set
- 1 × mounting screw pack
Optional: metal horn, sold separately.
How to size it
Torque tracks the rail: 18 kg·cm at 6.0 V, 22 at 7.4 V, 25 at 8.4 V. On a 2S pack that sits at 7.4 V under load, plan around 22 kg·cm and treat 25 as the fresh-pack figure.
Stall current is 4 A at 8.4 V against 410 mA no-load. Four of these on one BEC is 16 A at stall — the usual cause of a receiver brownout is exactly this, not the servo.
FAQ
How does it compare with a coreless servo of the same size?
Same 20 × 40 mm footprint and 25T spline, but no brushes to wear: service life is set by bearings and gears. It also runs cooler at the same output, which is what allows a fully sealed case.
What supply voltage?
6.0 to 8.4 V. The 25 kg·cm headline is the 8.4 V figure; at 7.4 V it is 22 kg·cm.
Is the pulse width table valid for this unit?
No. The microsecond window printed on the inspection sheet belongs to the PWM build of the same servo. This unit is commanded over the serial bus — ask for the command set and register map before writing firmware.
How many can share one bus?
The limit is the address space and the current budget of the shared supply, not the signal pair. Keep the bus ground common with the power ground at a single point.
Other interfaces
Downloads
- XQ-BLS8125TTL inspection specification (PDF, 767 KB)
Torque, speed and current at each supply voltage, mechanical data, control specification, mounting dimensions. - 2D dimension drawing (image)
Mounting hole positions, case depth and overall height; the same drawing is inside the datasheet.
